AGC 회로 원리.
A variation of amplifier gain , similar to the example, is necessary if we are going to compensate for input signal strength variations.
증폭기 이득의 변형이 필요하다. 우리는 입력 신호의 강도 변화를 보상하려고하는 경우의 예와 마찬가지로,
The required amplifier gain variations can be accomplished automatically by the addition of an agc circuit within the receiver.
요구되는 증폭기 이득 변화는 수신기 내에 AGC 회로를 추가함으로써 자동으로 달성될 수 있다.
Let's take a look at the methods and circuits used to produce agc and the manner in which agc (avc) controls receiver gain.
AGC를 생성하는데 사용된 방법과 회로 및 AGC (AVC)가 수신기 이득을 제어하는 방식을 살펴 보겠습니다.
Figure 2-15.
그림 2-15.
- Block diagram showing agc application.
- agc 응용을 보여주는 블록 다이어그램.
- Figure 2-15 is a block diagram representing agc feedback to preceding stages.
그림 2-15는 이전 단계에 대한 AGC 피드백을 나타내는 블록 다이어그램입니다.
The detector circuit has a dc component in the output that is directly proportional to the average amplitude of the modulated carrier.
검파기 회로는 변조된 반송파의 평균 진폭에 직접 비례하는 출력에서 DC 성분을 갖는다.
The agc circuitry uses this dc component by filtering the detector output to remove the audio and IF components and by applying a portion of the dc component to the preceding stages.
자동 이득 회로는 오디오를 제거하는 검파기 출력을 필터링 및 구성 요소 경우 선행 단계에 DC 성분의 일부를 적용함으로써 DC 성분을 사용한다.
This agc voltage controls the amplification of any or all of the stages preceding the detector stage.
이 AGC 전압은 검파기 단계 이전의 모든 스테이지 또는 모든 스테이지의 증폭을 제어합니다.
Solid-state receivers may use either positive or negative voltage for agc.
솔리드 스테이트 리시버는 AGC에 양 전압 또는 음 전압 중 하나를 사용할 수 있습니다.
The type of transistors used and the elements to which the control voltage is applied determine which type we will have.
사용되는 트랜지스터의 유형과 제어 전압이 적용되는 요소에 따라 우리가 가질 유형이 결정됩니다.
그림 2-16에 보여진 회로는 양의 AGC 전압을 생성합니다.
변압기 T1, 다이오드 CR1, 커패시터 C1, 저항기 R1 는 직렬 다이오드 검파기를 구성합니다.
The agc network is made up of R2 and C2.
AGC 네트워크는 R2와 C2로 구성됩니다.
With normal detector operation and the positive (+) potential shown at the input, CR1 conducts.
정상적인 검출기 동작과 입력단에 양의 (+) 전위가 표시되면, CR1이 도통합니다.
Conduction of the diode will cause a charging current (shown by the dashed line) to flow through agc capacitor C2 and agc resistor R2. 다이오드의 도체는 agc 커패시터 C2 및 agc 저항 R2를 통해 흐르는 충전 전류 (점선으로 표시)를 일으킬 것입니다.
This charging current develops a voltage across C2.
이 충전 전류는 C2을 따라서 전압을 발생시킨다.
When the potential across T1 reverses, the diode will be reverse biased and will not conduct.
T1 양단의 전위가 반전되면 다이오드는 역바이어스되고 전도되지 않습니다.
When this happens, the charging current ceases and C2 begins to discharge.
이 경우 충전 전류가 중단되고, C2가 방전하기 시작합니다.
The discharge path for C2 is shown by the solid arrows.
C2의 배출 경로는 실선 화살표로 표시됩니다.
The discharge path time constant of C2, R1, and R2 is chosen to be longer than the period (1/f) of the lowest audio frequency present in the output of the detector.
C2, R1 및 R2의 방전 경로 시정 수는 검파기의 출력에 있는 가장 낮은 오디오 주파수의 주기 (1 / f)보다 길도록 선택됩니다.
Because of the longer time constant, C2 will not discharge much between peaks of the modulating signal, and the voltage across C2 will be essentially a dc voltage.
더 긴 시간 상수로 인해 C2는 변조 신호의 피크 사이에서 많은 양을 방전하지 않으며, C2의 전압은 기본적으로 직류 전압이 됩니다.
This voltage is proportional to the average signal amplitude.
이 전압은 평균 신호 진폭에 비례합니다.
Now, if the signal strength varies, C2 will either increase or decrease its charge, depending on whether the signal increases or decreases.
이제 신호 강도가 변하면 C2는 신호의 증가 또는 감소에 따라 충전량을 늘리거나 줄입니다.
Since the charge on the agc capacitor responds only to changes in the average signal level, instantaneous variations in the signal will not affect the agc voltage. Ag
커패시터의 충전은 평균 신호 레벨의 변화에만 반응하기 때문에 신호의 순간 변동은 AGC 전압에 영향을 주지 않습니다.